17 Best Bolts For Concrete

10 Jul 2019

CONFAST 3 8 X 3 Stainless Steel Wedge Anchor 50 Per Box

CONFAST 3 8 X 3 Stainless Steel Wedge Anchor 50 Per Box
CONFAST 3 8 X 3 Stainless Steel Wedge Anchor 50 Per Box

CONFAST 3 8 X 3 Stainless Steel Wedge Anchor 50 Per Box. Environment The anchor is designed for use in a Wet environment. Torque Value To be set properly in the concrete, the anchor must be torqued to between 25 - 30 ft. HOLE SIZE IS ANCHOR SIZE - Simplicity and ease of installation. WIDE RANGE OF SIZES - Insures proper fastener for best results. Applications The anchor is made from 304 Stainless Steel. This anchor is designed for use in Concrete only, and should never be used in block or brick base material. The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill. Fixture Hole Diameter The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. MADE FROM 304 STAINLESS STEEL - Can be used in wet, submerged environments and will not rust. x 8 In. Bosch HC 2062 3 / 8 In. SDS-plus Bulldog Rotary Hammer Bit. CONFAST 1 / 2", x 3-3 / 4", Stainless Steel Wedge Anchor (25 per Box). Wedge Anchor 304 Stainless Steel - 3 / 8", 16 x 3", Qty-10. Hole Diameter / Bit Diameter The anchor requires a 3 / 8", hole to be drilled in the base material (Concrete only). Diameter of Anchor The diameter of the anchor is 3 / 8". Length Anchor The length of the anchor is 3", Thread Length The length of the threads on the anchor is 1-1 / 2", in length. Minimum Embedment The minimum anchor embedment into the concrete is 1-1 / 2". Therefore, the anchor must be installed so that a minimum of 1-1 / 2", of the anchor is embedded into the concrete. Maximum Fixture Thickness The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 1-1 / 8". This will ensure that the minimum embedment of 1-1 / 2", will be met. The 3 / 8", diameter anchor requires the hole in the fixture to be 1 / 2". Spacing between Anchors Each anchor must be spaced a minimum distance of 3-3 / 4", from each other when measured center to center. Edge Distance It is very not to install the anchor any closer than 1-7 / 8", from an unsupported edge of the concrete.

Simpson Strong Tie THD50400H 1 2 Inch By 4 Inch Titen HD Zinc Plated Heavy Duty Screw Anchor For Concrete Masonry 20 Per Pack

Simpson Strong Tie THD50400H 1 2 Inch By 4 Inch Titen HD Zinc Plated Heavy Duty Screw Anchor For Concrete Masonry 20 Per Pack
Simpson Strong Tie THD50400H 1 2 Inch By 4 Inch Titen HD Zinc Plated Heavy Duty Screw Anchor For Concrete Masonry 20 Per Pack

Simpson Strong Tie THD50400H 1 2 Inch By 4 Inch Titen HD Zinc Plated Heavy Duty Screw Anchor For Concrete Masonry 20 Per Pack. Specialized head treated process creates superior hardness. Recommended for permanent dry, interior non-corrosive environments or temporary outdoor applications. Tested per AC 193 to ensure outstanding performance in both cracked and uncracked concrete. The self-cutting, non-expansion characteristics of the Titen HD anchor make it ideal for structural applications, even at reduced edge distances and spacings. Designed to install using standard ANSI tolerance drill bits. It is design for cracked and uncracked concrete; a requirement that the 2009 IBC places on post-installed anchors. The Titen HD anchor is a patented, high strength screw for concrete and masonry. Simpson Strong Tie THD 37400 H 3 / 8-Inch by 4-Inch Titen HD Zinc Plated Heavy Duty Screw Anchor for Concrete / Masonry, 50 per Pack. Simpson Strong Tie THD 37300 H 3 / 8-Inch by 3-Inch Titen HD Zinc Plated Heavy Duty Screw Anchor for Concrete / Masonry, 50 per Pack. Simpson Strong Tie THD 50800 H 1 / 2-Inch by 8-Inch Titen HD Zinc Plated Heavy Duty Screw Anchor for Concrete / Masonry, 20 per Pack. Simpson Strong Tie THD 50600 H 1 / 2-Inch by 6-Inch Titen HD Zinc Plated Heavy Duty Screw Anchor for Concrete / Masonry, 20 per Pack. SDS-plus Bulldog Rotary Hammer Bit. x 6 In. Simpson Strong Tie THD 50500 H 1 / 2-Inch by 5-Inch Titen HD Zinc Plated Heavy Duty Screw Anchor for Concrete / Masonry, 20 per Pack. Rectorseal 23631 1 / 4 Pint Brush Top T Plus 2 Pipe Thread Sealant. Zipwall Foam Rail Span Adjustable Tapeless Seal, SPN. Bosch HC 2011 3 / 16 In. THD 50400 H 1 / 2", x 4", Titen HD Heavy Duty Screw Anchors 20 / pk. Bosch HC 2081 1 / 2 In. Easy post-installation inspection head stamped with anchor length in inches. Threads along the length of the anchor undercut the concrete and efficiently transfer the load to the base material.

The Hillman Group 372057 Hammer Drive Anchor 1 4 X 1 1 4 Inch 100 Pack

The Hillman Group 372057 Hammer Drive Anchor 1 4 X 1 1 4 Inch 100 Pack
The Hillman Group 372057 Hammer Drive Anchor 1 4 X 1 1 4 Inch 100 Pack

The Hillman Group 372057 Hammer Drive Anchor 1 4 X 1 1 4 Inch 100 Pack. 100-Pieces per pack.

Wej It Wej Con Concrete Screws 100 Pack Drill Bit Included Carbon Steel Corrosion Resistant For Indoor Outdoor Home Office Improvement Hex Washer Head With Slotted Drive 3 16 X 1 1 4

Wej It Wej Con Concrete Screws 100 Pack Drill Bit Included Carbon Steel Corrosion Resistant For Indoor Outdoor Home Office Improvement Hex Washer Head With Slotted Drive 3 16 X 1 1 4
Wej It Wej Con Concrete Screws 100 Pack Drill Bit Included Carbon Steel Corrosion Resistant For Indoor Outdoor Home Office Improvement Hex Washer Head With Slotted Drive 3 16 X 1 1 4

Wej It Wej Con Concrete Screws 100 Pack Drill Bit Included Carbon Steel Corrosion Resistant For Indoor Outdoor Home Office Improvement Hex Washer Head With Slotted Drive 3 16 X 1 1 4. To furnish a secure hold without requiring threaded inserts, this high-strength, case hardened screw is outfitted with twin-lead, v-notched threads for anchoring into concrete, hollow block, brick, mortar and concrete masonry units. To accommodate your needs, the Hew Washer Head and the Phillips Flat Head Concrete Screws come in a variety of different sizes. The hex washer has a linear slot for use with a flat-blade driver, as well as six flat sides that a wrench can grip. Conforming to American Society for Testing and Materials (ASTM) B 117 this coating will resist 1, 000 hours of salt spray. Meanwhile, the Phillips drive has an x-shaped slot which accepts a Phillips driver. This Wej-It Wej-Con Concrete Screw is crafted using 1022 carbon steel with a corrosion-resistant, blue R-Blocker finish to supply long-term strength and use. DURABLE CONSTRUCTION. The hex washer head has a flange that provides additional bearing surface to distribute the clamping force over a larger area, reducing damage to the fixture being fastened, while the flat head is cone shaped for use in countersunk holes and has a flat top that fits flush with the mated surface when installed, giving your work a neat finish. DIFFERENT HEAD STYLES. New! High-Pressure Shower Head 5-Setting - 4", Luxury Chrome Shower-head - Powerful Shower Spray Even with Low Water Pressure in Supply Pipeline - Low Flow Water Efficient Showerhead - Easy Installation. Strongest Magnetic Knife Strip - By Kaizen Cutlery - Magnetic Knife Holder with Multi Purpose Functionality as 12 Inch Knife Magnet, Knife Storage, Magnetic Organizer- Securely Holds Knives. Lavalier Lapel Microphone 2-Pack Complete Set - Omnidirectional Mic for Desktop PC Computer, Mac, Smartphone, i Phone, Go Pro, DSLR, Camcorder for Podcast, Youtube, Vlogging, and DJs. Kuche Pro 12-Piece Silicone Kitchen Utensil Set - Premium Natural Beech Wooden Handles with Non-Stick Silicone Heat Resistant Cookware for Cooking and Baking Tools - Green. Super Slow Rising Squishies Pack. Squishy Jumbo Deer Set of Large Soft Scented Cute Kawaii, Colorful Animal Stress Relief Toy for Kids and Adults. Amazing Squeeze Toys. Corn remover for feet-salicylic acid pads to cushion your foot with powerful medicine for the professional treatment of tough to remove corns, warts and calluses on toes and feet. ONZOLO Velvet Scrunchies For Hair - Hair Accessories For Women and Girls, Hair Ties for Thick Hair, Velvet Scrunchie, Hair Bands, Women's Hair Elastics, Little Girl Hair Accessories, Headband (6 pack). K che Pro 100 Pack 9 oz Gold Rim Clear Plastic Cups - Disposable Plastic Wine Glasses for Parties, Birthdays, Fancy Cups for Kids, Bridal Showers, Fancy Cups for Wedding and Other Holiday Plastic Cups. Flexzos Advanced Dual Power Electric Plug in Ultrasonic Pest Repeller for Flies, Mosquitos, Mice, Rodents, Spiders and Other Bugs Types of Family Rooms, Kitchen or Kids Room. Brook Bay Faux Fur Pom Pom Beanie - Stay Warm Stylish - Thick, Soft Chunky Cable Knit Beanie - Winter Hats for Women Men - Serious Beanies for Serious Style. It is recommended that a minimum of 1-inch and a maximum of 13-inch embedment be used in determining fastener length.

25 1 4X5 Hex Lag Screws Hot Dip Galvanized Screw Assortment Kit Set

25 1 4X5 Hex Lag Screws Hot Dip Galvanized Screw Assortment Kit Set
25 1 4X5 Hex Lag Screws Hot Dip Galvanized Screw Assortment Kit Set

25 1 4X5 Hex Lag Screws Hot Dip Galvanized Screw Assortment Kit Set. In the catalog, you are offered assorted nut and bolt kit, plastic cap washers, screws for treated wood, metric fasteners of different standards, shapes, depending on the specifics of using models for screw set. Therefore, even when used in difficult conditions with high humidity are characterized by durability and reliability. We offer a great choice of self tapping screws, Machine Screws, Socket Head Screws, hard drive screws, m 3 m 2 m 4 screws, Wood Screws, Sheet Metal Screws. OUR PROFESSIONAL LICENSE PLATE SCREWS are often located in a position that makes screw kit susceptible to corrosion and therefore is an obvious choice both in terms of weight saving, appearance, and performance. FANTASTIC CORROSION RESISTANCE. They are intended for both manual and automatic screwing, twisting and tightening with the maximum force developed by any tool. The metric hardware kits presented in the assortment find application in the spheres of construction of metal structures, in the construction industry, in mechanical engineering, in the field of repair and restoration works. All metric hardware assortment presented in the fastener are in accordance with accepted norms and are approved for use. STAINLESS STEEL CONCRETE SCREWS ARE RELIABLE AND DURABLE and are used in many applications. CHOOSE OUR DECK SCREWS FOR GENERAL PURPOSE USE. All stainless steel license plate screws are made of corrosion-protected steel. They are able to withstand increased mechanical, vibration and thermal loads without changing the original characteristics, providing a strong attachment. FASTENERS - THE BEST DECISION IN REPAIR WORKS! A variety of metric hardware allows you to bolt screw assortment, washers, screws, screws for wood, replacement parts, crib hardware, which available in a various styles and materials. A set screw is used widely in the home and office appliance, communication equipment and other machinery industry. The quality bolt kit, star head screws, nut driver organizers demonstrate considerable strength and high wear resistance. It is widely used both for private repairs and for fixing parts of large production facilities.

CONFAST 5 8 X 6 Stainless Steel Wedge Anchor 20 Per Box

CONFAST 5 8 X 6 Stainless Steel Wedge Anchor 20 Per Box
CONFAST 5 8 X 6 Stainless Steel Wedge Anchor 20 Per Box

CONFAST 5 8 X 6 Stainless Steel Wedge Anchor 20 Per Box. Fixture Hole Diameter The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. This anchor is designed for use in Concrete only, and should never be used in block or brick base material. Torque Value To be set properly in the concrete, the anchor must be torqued to between 75 - 90 ft. MADE FROM 304 STAINLESS STEEL - Can be used in wet, submerged environments and will not rust. The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill. Applications The anchor is made from 304 Stainless Steel. WIDE RANGE OF SIZES - Insures proper fastener for best results. HOLE SIZE IS ANCHOR SIZE - Simplicity and ease of installation. Environment The anchor is designed for use in a Wet environment. Hole Diameter / Bit Diameter The anchor requires a 5 / 8", hole to be drilled in the base material (Concrete only). Diameter of Anchor The diameter of the anchor is 5 / 8". Length Anchor The length of the anchor is 6", Thread Length The length of the threads on the anchor is 3-3 / 4", in length. Minimum Embedment The minimum anchor embedment into the concrete is 2-3 / 4". Therefore, the anchor must be installed so that a minimum of 2-3 / 4", of the anchor is embedded into the concrete. Maximum Fixture Thickness The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 2-5 / 8". This will ensure that the minimum embedment of 2-3 / 4", will be met. The 5 / 8", diameter anchor requires the hole in the fixture to be 7 / 8". Spacing between Anchors Each anchor must be spaced a minimum distance of 6-1 / 4", from each other when measured center to center. Edge Distance It is very not to install the anchor any closer than 3-1 / 8", from an unsupported edge of the concrete.

Wej It Sleeve TITE HSA1230 Sleeve Anchor Carbon Steel Zinc Plated Finish Hex Head Meets GSA FFS 325 Group II Type 3 Class 3 1 2 Diameter 3 Length 3 8 16 Threads Pack Of 25

Wej It Sleeve TITE HSA1230 Sleeve Anchor Carbon Steel Zinc Plated Finish Hex Head Meets GSA FFS 325 Group II Type 3 Class 3 1 2 Diameter 3 Length 3 8 16 Threads Pack Of 25
Wej It Sleeve TITE HSA1230 Sleeve Anchor Carbon Steel Zinc Plated Finish Hex Head Meets GSA FFS 325 Group II Type 3 Class 3 1 2 Diameter 3 Length 3 8 16 Threads Pack Of 25

Wej It Sleeve TITE HSA1230 Sleeve Anchor Carbon Steel Zinc Plated Finish Hex Head Meets GSA FFS 325 Group II Type 3 Class 3 1 2 Diameter 3 Length 3 8 16 Threads Pack Of 25. Anchors provide reinforcement to fasteners installed in materials that are considered brittle or have insufficient hold such as drywall, concrete, brick, and stone. Wej-It Fastening Systems manufactures mechanical and adhesive fasteners for use in concrete and drywall. The company, founded more than 60 years ago, is headquartered in Norwalk, CT. The Wej-it Sleeve-TITE HSA 1230 with hex nut head is made of zinc-plated carbon steel, provides a secure hold in most materials including normal weight and lightweight concrete, solid masonry, and hollow masonry, and meets GSA FFS-325 Group II, Type 3, Class 3 federal The anchor consists of a zinc-plated carbon steel body, spacer, and sleeve, which expands to secure the anchor in place when the nut is tightened and has indentations for enhanced grip. Anchor consists of a zinc-plated carbon steel body, spacer, and sleeve, which expands to secure the anchor in place. Sleeve anchor with hex nut head provides a secure hold in most materials, including normal weight and lightweight concrete, solid masonry, and hollow masonry. Use one-fourth or less of listed maximum values for safe working loads (as required by local regulations). Ultimate tensile strength for static loads 4, 649 lb. For more information, see the sheet. GSA FFS-325 Group II, Type 3, Class 3. Anchors provide support through methods such as expansion from within or behind the substrate, or insertion of adhesive compounds into drilled holes. The hex nut head tightens with a wrench separately) and comes assembled with the spacer onto the anchor for ease of Part Number Anchor Size Drill Diameter Thread Size Minimum Embedment Depth Ultimate tensile strength for static loads in 4, 000-psi solid concrete at embedment depth Ultimate shear strength for static loads in 4, 000-psi solid concrete at embedment depth HSA 56125 / 16", x 1-1 / 2", 5 / 16", 1 / 4", 201-1 / 4", 1, 630 lb. at 1-3 / 16", 2, 225 lb. at 1-3 / 16", HSA 56225 / 16", x 2-1 / 2", 5 / 16", 1 / 4", 201-1 / 4", 2, 181 lb. at 2-1 / 16", 2, 311 lb. at 2-1 / 16", HSA 38133 / 8", x 1-7 / 8", 3 / 8", 5 / 16", 181-1 / 2", 2, 502 lb. at 1-1 / 4", 3, 116 lb. at 1-1 / 4", HSA 38303 / 8", x 3", 3 / 8", 5 / 16", 181-1 / 2", 3, 046 lb. at 2-1 / 2", 3, 691 lb. at 2-1 / 2", HSA 12211 / 2", x 2-1 / 4", 1 / 2", 3 / 8", 161-7 / 8", 2, 656 lb. at 1-1 / 2", 3, 724 lb. at 1-1 / 2", HSA 12301 / 2", x 3", 1 / 2", 3 / 8", 161-7 / 8", 4, 649 lb. at 2-3 / 8", 2, 726 lb. at 2-3 / 8", HSA 12401 / 2", x 4", 1 / 2", 3 / 8", 161-7 / 8", 5, 127 lb. at 3-3 / 8", 4, 726 lb. at 3-3 / 8", HSA 12601 / 2", x 6", 1 / 2", 3 / 8", 161-7 / 8", 5, 127 lb. at 3-3 / 8", 4, 726 lb. at 3-3 / 8", HSA 58215 / 8", x 2-1 / 4", 5 / 8", 1 / 2", 132", 4, 568 lb. at 2-1 / 4", 5, 218 lb. at 2-1 / 4", HSA 58305 / 8", x 3", 5 / 8", 1 / 2", 132", 4, 568 lb. at 2-1 / 4", 5, 218 lb. at 2-1 / 4", HSA 58415 / 8", x 4-1 / 4", 5 / 8", 1 / 2", 132", 7, 285 lb. at 3-15 / 16", 6, 747 lb. at 3-15 / 16", HSA 58605 / 8", x 6", 5 / 8", 1 / 2", 132", 7, 631 lb. at 5-7 / 16", 7, 689 lb. at 5-7 / 16", HSA 34223 / 4", x 2-1 / 2", 3 / 4", 5 / 8", 112-1 / 4", 5, 388 lb. at 1-7 / 8", 7, 862 lb. at 1-7 / 8", HSA 34403 / 4", x 4", 3 / 4", 5 / 8", 112-1 / 4", 6, 219 lb. at 3-9 / 16", 9, 786 lb. at 3-9 / 16", HSA 34613 / 4", x 6-1 / 4", 3 / 4", 5 / 8", 112-1 / 4", 6, 456 lb. at 5-1 / 2", 10, 073 lb. at 5-1 / 2", Warning: Use one-fourth or less of listed maximum values for safe working loads (as required by local regulations). at 2-3 / 8", embedment depth in 4, 000-psi solid concrete.

Mobile Home Parts Set Of 12 Dry Concrete Anchors Tie Down Straps And Bolts

Mobile Home Parts Set Of 12 Dry Concrete Anchors Tie Down Straps And Bolts
Mobile Home Parts Set Of 12 Dry Concrete Anchors Tie Down Straps And Bolts

Mobile Home Parts Set Of 12 Dry Concrete Anchors Tie Down Straps And Bolts. Mobile Home Tie Down Anchor Kit. Designed for use with cured concrete. Tie Down Engineering 59135 N Slotted Bolt and Nut.

ZRM E 5Pcs M8x100mm Expanding Shield Anchor Eye Bolts 304 Stainless Steel Fastener Raw Style Sleeve Expansion Screw With Eye Ring For Cable Rope Lifting

ZRM E 5Pcs M8x100mm Expanding Shield Anchor Eye Bolts 304 Stainless Steel Fastener Raw Style Sleeve Expansion Screw With Eye Ring For Cable Rope Lifting
ZRM E 5Pcs M8x100mm Expanding Shield Anchor Eye Bolts 304 Stainless Steel Fastener Raw Style Sleeve Expansion Screw With Eye Ring For Cable Rope Lifting

ZRM E 5Pcs M8x100mm Expanding Shield Anchor Eye Bolts 304 Stainless Steel Fastener Raw Style Sleeve Expansion Screw With Eye Ring For Cable Rope Lifting. The screw bigger head will expand the metal sheath to hang on the wall till the bolt can not be pulled out. Solid structure, strong load bearing, sturdy and durable in use. Type: Expanding Shield Anchor Eye Bolts Size: M 8 x 100 mm Color: Silver Made from high quality environmental protection 304 stainless steel, solid structure, strong load bearing, high hardness, non-deformation, wear-proof, rust and corrosion resistance, durable in use, long service life. Mainly used to build a anchor point in brick, concrete and other masonry for wires, signs, electrics, suspended ceilings etc. How to Install: Drill a hole in the wall with the size of the expansion pipe. Widely applied for fence, burglarproof doors and windows, canopy, air conditioning rack fixation, home decoration, engineering, etc. Insert the expansion bolt into the hole and then tighten the nuts with wrench. Suitable for wire rope lifting. Easy to install, convenient to use. Made from high quality environmental protection 304 stainless steel, high hardness, non-deformation, wear-proof, rust and corrosion resistance, long service life.

Uxcell M6 X 50 Expansion Eyebolt Eye Nut Screw With Ring 304 Stainless Steel Anchor Raw Bolts 4 Pcs

Uxcell M6 X 50 Expansion Eyebolt Eye Nut Screw With Ring 304 Stainless Steel Anchor Raw Bolts 4 Pcs
Uxcell M6 X 50 Expansion Eyebolt Eye Nut Screw With Ring 304 Stainless Steel Anchor Raw Bolts 4 Pcs

Uxcell M6 X 50 Expansion Eyebolt Eye Nut Screw With Ring 304 Stainless Steel Anchor Raw Bolts 4 Pcs. The eye type is drop forged eye, such eye bolts are designed to attach a securing eye to a structure and then tie to ropers or cables. hole for drilling, and tight the anchor bolt with a wrench after putting the screw. Total Weight: 144 g Materials: 304 Stainless Steel Application: Concrete and masonry Content: 4 x pcs M 6 x 50 Expansion Eye Bolt. Made of premium 304 stainless steel, provides a rust protection and precise size. Fit the concrete wall or masonry, for hanging or lefting the super heavy things like a big shelf. It's durable and reliable. Suggested a 10 mm Dia. The bolt transfers forces to the sleeve, with the expansion of sleeve, a solid connection has been built between a concrete wall and the wedge anchor nut. Screw Size: M 6 Overall Length: 75 mm Eye Nut Height: 30 mm Inner diameter of the ring: 16 mm Sleeve Inner Diameter: 6 mm Sleeve Length: 35 mm Suggested Hole Size: 10 mm Dia. Standard M 6 expansion bolts with 75 mm length, and the ring Inner Diameter is 16 mm.

The Hillman Group 260390 1 1 1 5 8 X 18 Inch Anchor Bolt 10 Pack

The Hillman Group 260390 1 1 1 5 8 X 18 Inch Anchor Bolt 10 Pack
The Hillman Group 260390 1 1 1 5 8 X 18 Inch Anchor Bolt 10 Pack

The Hillman Group 260390 1 1 1 5 8 X 18 Inch Anchor Bolt 10 Pack. For use in wood or concrete projects. They can also be used to firmly affix embed plates to a concrete foundation when used with a structural steel element. Not Recommended with treated lumber. There are many types of anchor bolts, consisting of designs that are mostly proprietary to the manufacturing companies. All bolts consist of a threaded end, to which a nut and washer can be attached for the external load. Anchor bolts are extensively used on all types of projects, from standard buildings to dams and nuclear power plants. An Anchor Bolt is used to attach objects or structures to concrete.

CONFAST 3 8 X 3 3 4 Wedge Anchor Zinc Plated Box Of 50

CONFAST 3 8 X 3 3 4 Wedge Anchor Zinc Plated Box Of 50
CONFAST 3 8 X 3 3 4 Wedge Anchor Zinc Plated Box Of 50

CONFAST 3 8 X 3 3 4 Wedge Anchor Zinc Plated Box Of 50. WIDE RANGE OF SIZES - Insures proper fastener for best results. The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill. Applications The anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete only, and should never be used in block or brick base material. Torque Value To be set properly in the concrete, the anchor must be torqued to between 25 - 30 ft. ZINC PLATED - Helps prevent rust in dry environments. Environment The anchor is designed for use in a Dry environment. HOLE SIZE IS ANCHOR SIZE - Simplicity and ease of installation. Fixture Hole Diameter The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. Bosch LBH 008 3 / 8 x 6 Round Hammer Drill Bit. CONFAST 1 / 2", x 5-1 / 2", Wedge Anchor Zinc Plated (Box of 25). CONFAST 1 / 2", x 4-1 / 4", Wedge Anchor Zinc Plated (Box of 25). 10 Piece Masonry Drill Bits Set (TILE, BRICK, CEMENT, CONCRETE, GLASS, PLASTIC, CINDERBLOCK, WOOD) Chrome Plated with Industrial Strength Carbide Tips - BONUS STORAGE CASE INCLUDED. Hole Diameter / Bit Diameter The anchor requires a 3 / 8", hole to be drilled in the base material (Concrete only). Diameter of Anchor The diameter of the anchor is 3 / 8". Length Anchor The length of the anchor is 3-3 / 4", Thread Length The length of the threads on the anchor is 2-1 / 2", in length. Minimum Embedment The minimum anchor embedment into the concrete is 1-1 / 2". Therefore, the anchor must be installed so that a minimum of 1-1 / 2", of the anchor is embedded into the concrete. Maximum Fixture Thickness The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 1-7 / 8". This will ensure that the minimum embedment of 1-1 / 2", will be met. The 3 / 8", diameter anchor requires the hole in the fixture to be 1 / 2". Spacing between Anchors Each anchor must be spaced a minimum distance of 3-3 / 4", from each other when measured center to center. Edge Distance It is very not to install the anchor any closer than 1-7 / 8", from an unsupported edge of the concrete.

CONFAST 3 8 X 3 1 2 Wedge Anchor Zinc Plated Box Of 50

CONFAST 3 8 X 3 1 2 Wedge Anchor Zinc Plated Box Of 50
CONFAST 3 8 X 3 1 2 Wedge Anchor Zinc Plated Box Of 50

CONFAST 3 8 X 3 1 2 Wedge Anchor Zinc Plated Box Of 50. This anchor is designed for use in Concrete only, and should never be used in block or brick base material. ZINC PLATED - Helps prevent rust in dry environments. HOLE SIZE IS ANCHOR SIZE - Simplicity and ease of installation. Environment The anchor is designed for use in a Dry environment. The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill. WIDE RANGE OF SIZES - Insures proper fastener for best results. Torque Value To be set properly in the concrete, the anchor must be torqued to between 25 - 30 ft. Fixture Hole Diameter The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. Applications The anchor is made from Carbon Steel, and is Zinc Plated. Makita 7 Piece - Complete Concrete Drill Bit Set For Hammer Drills - Precise Drilling For Masonry Concrete - Tungsten Carbide Bits. DEWALT DW 5230 3 / 8-Inch x 6-Inch Carbide Hammer Drill Bit. Hole Diameter / Bit Diameter The anchor requires a 3 / 8", hole to be drilled in the base material (Concrete only). Diameter of Anchor The diameter of the anchor is 3 / 8". Length Anchor The length of the anchor is 3-1 / 2", Thread Length The length of the threads on the anchor is 2-1 / 4", in length. Minimum Embedment The minimum anchor embedment into the concrete is 1-1 / 2". Therefore, the anchor must be installed so that a minimum of 1-1 / 2", of the anchor is embedded into the concrete. Maximum Fixture Thickness The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 1-5 / 8". This will ensure that the minimum embedment of 1-1 / 2", will be met. The 3 / 8", diameter anchor requires the hole in the fixture to be 1 / 2". Spacing between Anchors Each anchor must be spaced a minimum distance of 3-3 / 4", from each other when measured center to center. Edge Distance It is very not to install the anchor any closer than 1-7 / 8", from an unsupported edge of the concrete.

1 4 X 2 1 4 Powers Wedge Bolts Concrete Anchor Zinc Plated 100

1 4 X 2 1 4 Powers Wedge Bolts Concrete Anchor Zinc Plated 100
1 4 X 2 1 4 Powers Wedge Bolts Concrete Anchor Zinc Plated 100

1 4 X 2 1 4 Powers Wedge Bolts Concrete Anchor Zinc Plated 100.

CONFAST 3 8 Inside Screw 3 8 Diameter 304 Stainless Steel Drop In Anchor With 1 Setting Tool 50 Per Box

CONFAST 3 8 Inside Screw 3 8 Diameter 304 Stainless Steel Drop In Anchor With 1 Setting Tool 50 Per Box
CONFAST 3 8 Inside Screw 3 8 Diameter 304 Stainless Steel Drop In Anchor With 1 Setting Tool 50 Per Box

CONFAST 3 8 Inside Screw 3 8 Diameter 304 Stainless Steel Drop In Anchor With 1 Setting Tool 50 Per Box. Environment The anchor is designed for use in a Wet environment. Can only be used in solid concrete. For use in dry, indoor applications. This anchor is designed for use in Concrete only, and should never be used in block or brick base material. Designated diameter equals inside diameter. FLUSH MOUNT - Nothing sticks up above surface of the concrete. The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill. Applications The anchor is made from 304 Stainless Steel. Bosch HCSTP 2083 1 / 2 In. 3 / 8-16 x 1-1 / 4", Button Head Socket Cap Screws, Allen Socket Drive, Stainless Steel 18-8, Full Thread, Bright Finish, Machine Thread, Quantity 10 By Fastenere. Prime-Line 9059581 Hex Bolts, 3 / 8 in. 3 / 8", Stainless Flat Finish Washer 7 / 8", OD (100 pc) by Bolt Dropper, 18-8 (304) Stainless Steel. The Hillman Group 830670 Stainless Steel 3 / 8-Inch Split Lock Washer, (100 x 1 Pack). CONFAST 1 / 2", (Inside / Screw 1 / 2", 13 Diameter Threads) 304 Stainless Steel Drop-in Anchor with 1 Setting Tool (50 per Box). SDS-plus Hammer Drill Chisel Set, Rotary Hammer Bits Set, 3 PCS Including Point Chisel, Flat Chisel, Cranked Chisels With Carry Case. Grade 304 Stainless Steel, 25-Pack. x 1-11 / 16 In. SDS-plus Stop Bit. 16 X 1 in. Stainless 3 / 8-16 X 1-1 / 4 Hex Head Bolts (3 / 4 To 5", Length in Listing), 304 Stainless Steel, 25 pieces (3 / 8-16 X 1-1 / 4). Stainless 3 / 8-16 X 1 Hex Head Bolts (3 / 4 To 5", Length in Listing), 304 Stainless Steel, 25 pieces (3 / 8-16 X 1). Hillman 830506 Stainless Steel 3 / 8-Inch Flat Washers, 100-Pack, Single. Hole Diameter / Bit Diameter The anchor requires a 1 / 2", hole to be drilled in the base material (Concrete only). Minimum Embedment The minimum anchor embedment into the concrete is 1-9 / 16". Therefore, the anchor must be installed so that a minimum of 1-9 / 16", of the anchor is embedded into the concrete. Spacing between Anchors Each anchor must be spaced a minimum distance of 5", from each other when measured center to center. Edge Distance It is very not to install the anchor any closer than 2-1 / 2", from an unsupported edge of the concrete.

CONFAST 5 8 X 6 Wedge Anchor Zinc Plated Box Of 20

CONFAST 5 8 X 6 Wedge Anchor Zinc Plated Box Of 20
CONFAST 5 8 X 6 Wedge Anchor Zinc Plated Box Of 20

CONFAST 5 8 X 6 Wedge Anchor Zinc Plated Box Of 20. HOLE SIZE IS ANCHOR SIZE - Simplicity and ease of installation. Environment The anchor is designed for use in a Dry environment. This anchor is designed for use in Concrete only, and should never be used in block or brick base material. ZINC PLATED - Helps prevent rust in dry environments. Applications The anchor is made from Carbon Steel, and is Zinc Plated. The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill. WIDE RANGE OF SIZES - Insures proper fastener for best results. Fixture Hole Diameter The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. Torque Value To be set properly in the concrete, the anchor must be torqued to between 75 - 90 ft. Simpson Strong Tie Wa 62600 5 / 8-Inch by 6-Inch with 4-3 / 8-Inch Thread Length Zinc Plated Steel Wedge-All Anchor, 20-Piece. Bosch HC 2081 1 / 2 In. DEWALT DW 5446 5 / 8-Inch x 6-Inch x 8-Inch ROCK CARBIDE SDS Plus Hammer Bit. CONFAST 1 / 2", x 5-1 / 2", Wedge Anchor Zinc Plated (Box of 25). x 6 In. CONFAST 5 / 8", x 4-1 / 2", Wedge Anchor Zinc Plated (Box of 25). SDS-plus Bulldog Rotary Hammer Bit. CONFAST 5 / 8", x 5", Wedge Anchor Zinc Plated (Box of 20). Hole Diameter / Bit Diameter The anchor requires a 5 / 8", hole to be drilled in the base material (Concrete only). Diameter of Anchor The diameter of the anchor is 5 / 8". Length Anchor The length of the anchor is 6", Thread Length The length of the threads on the anchor is 4", in length. Minimum Embedment The minimum anchor embedment into the concrete is 2-3 / 4". Therefore, the anchor must be installed so that a minimum of 2-3 / 4", of the anchor is embedded into the concrete. Maximum Fixture Thickness The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 2-5 / 8". This will ensure that the minimum embedment of 2-3 / 4", will be met. The 5 / 8", diameter anchor requires the hole in the fixture to be 7 / 8". Spacing between Anchors Each anchor must be spaced a minimum distance of 6-1 / 4", from each other when measured center to center. Edge Distance It is very not to install the anchor any closer than 3-1 / 8", from an unsupported edge of the concrete.

CONFAST 3 8 X 5 Wedge Anchor Zinc Plated Box Of 50

CONFAST 3 8 X 5 Wedge Anchor Zinc Plated Box Of 50
CONFAST 3 8 X 5 Wedge Anchor Zinc Plated Box Of 50

CONFAST 3 8 X 5 Wedge Anchor Zinc Plated Box Of 50. Torque Value To be set properly in the concrete, the anchor must be torqued to between 25 - 30 ft. WIDE RANGE OF SIZES - Insures proper fastener for best results. Fixture Hole Diameter The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. Environment The anchor is designed for use in a Dry environment. ZINC PLATED - Helps prevent rust in dry environments. Applications The anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete only, and should never be used in block or brick base material. HOLE SIZE IS ANCHOR SIZE - Simplicity and ease of installation. The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill. DEWALT DW 5207 7-Piece Premium Percussion Masonry Drill Bit Set. 25 Pack Black Hawk 4-1 / 2", 045 x 7 / 8", Arbor Depressed Center Cut Off Wheels - Metal Stainless Steel Type 27. Bosch 7 Piece Carbide-Tipped SDS-plus Rotary Hammer Drill Bit Set with Storage Case HCK 001. CONFAST 1 / 2", x 5-1 / 2", Wedge Anchor Zinc Plated (Box of 25). Simpson Strong Tie WA 37334 3 / 8-Inch by 3-3 / 4-Inch Zinc Plated Steel Wedge-All Anchor with 2-5 / 8-Inch Thread Length, 50-Pack. Bosch HC 2061 3 / 8 In. Gasoila Soft-Set Pipe Thread Sealant with PTFE Paste, Non Toxic, 100 to 600 Degree F, 1 / 4 Pint Brush. Makita 10 Pack - 4.5", Cut Off Wheels For Grinders - Aggressive Cutting For Metal Stainless Steel / INOX - 4-1 / 2", 045 x 7 / 8-Inch. DEWALT DW 5230 3 / 8-Inch x 6-Inch Carbide Hammer Drill Bit. Bosch LBH 008 3 / 8 x 6 Round Hammer Drill Bit. SDS-plus Bulldog Rotary Hammer Bit. x 6 In. Hole Diameter / Bit Diameter The anchor requires a 3 / 8", hole to be drilled in the base material (Concrete only). Diameter of Anchor The diameter of the anchor is 3 / 8". Length Anchor The length of the anchor is 5", Thread Length The length of the threads on the anchor is 3-3 / 4", in length. Minimum Embedment The minimum anchor embedment into the concrete is 1-1 / 2". Therefore, the anchor must be installed so that a minimum of 1-1 / 2", of the anchor is embedded into the concrete. Maximum Fixture Thickness The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 3-1 / 8". This will ensure that the minimum embedment of 1-1 / 2", will be met. The 3 / 8", diameter anchor requires the hole in the fixture to be 1 / 2". Spacing between Anchors Each anchor must be spaced a minimum distance of 3-3 / 4", from each other when measured center to center. Edge Distance It is very not to install the anchor any closer than 1-7 / 8", from an unsupported edge of the concrete.